Proudly Servicing South Denver Metro
Rated 4.9 on Google
Boiler Maintenance in Cherry Hills Village, Littleton & Greenwood Village

Mountain Standard Plumbing provides boiler maintenance for homeowners in Cherry Hills Village, Littleton, and Greenwood Village. Our visit inspects, cleans, tests, and adjusts your hot water boiler and the hydronic system around it so it heats reliably through a Front Range winter.
Many homes in these communities were built between the 1950s and the 1980s, and many of the larger custom homes heat with boilers feeding baseboard, radiators, or radiant floors. We look at the boiler and the whole system it serves, because most heating complaints we see start in the piping, controls, or water inside the loop.

What Our Boiler Maintenance Includes
A surface-level check means firing the boiler, confirming it makes heat, and leaving. That tells you little about how it will hold up on a subzero night. A thorough visit looks at combustion, water condition, pressure, safety controls, and circulation.
- Combustion testing: we measure flue gases with an analyzer and adjust the burner for our elevation.
- Burner and heat exchanger: we check for soot, scale, corrosion, and cracks, and clean what can be cleaned.
- Venting and condensate: we confirm the vent is intact and clear, and that condensing units drain properly.
- Pressure and expansion tank: we verify system pressure and test the tank’s air charge.
- Safety controls: we test the relief valve, high-limit control, and low-water cutoff where installed.
- Circulators and zones: we check that each zone opens, closes, and moves water as it should.
- System water and controls: we check the water in the loop and review outdoor reset and thermostat settings.
If we find something beyond routine maintenance, such as a failing circulator or a weeping relief valve, we show you what we found and quote the repair before any work begins.
Get your boiler checked before the next cold front. Schedule boiler maintenance and we will set up a visit that fits your schedule.
Combustion Adjustment at Our Elevation
These communities sit more than a mile above sea level, where the air is thinner. A burner set up for sea-level conditions can run rich here, produce excess carbon monoxide, and soot the heat exchanger over time.
We do not adjust a burner by sight or sound. We read oxygen, carbon monoxide, and flue temperature with an analyzer and set the burner to the manufacturer’s high-altitude specifications. If your boiler was never properly set up for altitude, we will tell you and explain what correcting it involves.
Water Inside the Loop
A closed hydronic loop should hold the same water for years. When a system loses water through a small leak or a weeping relief valve, an automatic fill valve keeps adding fresh water. Our water carries enough minerals that each new fill adds scale to the heat exchanger, and the oxygen it brings speeds corrosion.
A loop that keeps taking on water almost always has a leak, and finding it matters more than treating the water. If the leak is in piping rather than the boiler, our water leak detection and repair service can track it down.
Older Systems, Newer Systems, and Mixed Zones
Older homes here often have cast iron boilers with zones added during remodels. An addition tied into the original loop can leave one zone starved for flow while another overheats, a pattern we cover in more detail in why your boiler isn’t heating evenly. Newer and remodeled homes may have condensing boilers serving radiant floors, a snowmelt loop, or an indirect water heater, all of which rely on mixing valves and controls set correctly.
We check how each zone performs, not just whether the boiler fires. Problems with a separate indirect tank are handled through our water heater service. Maintenance cannot fix a zone that was undersized or piped incorrectly from the start, and if we see that, we explain the options separately.
Safety Controls Before the Cold Arrives
Relief valves can seize from mineral buildup, expansion tanks lose their air charge, and low-water cutoffs can fail with no visible sign. None of these shows up as a comfort complaint until it becomes a serious one.
Our weather can swing from a mild afternoon to well below zero within a day when an arctic front comes down the Front Range. A boiler suddenly running at full fire for days is when a weak control tends to fail, so we test these on every visit.
A Common Misconception About Topping Off
Many homeowners believe a boiler simply needs air bled and water added each fall. A system that needs water every season is losing it somewhere, usually through a leak, a failing relief valve, or an expansion tank that has lost its charge. Topping off year after year treats the symptom and keeps adding the minerals and oxygen that shorten the boiler’s life, so we look for the cause instead.
How Often Boilers Should Be Serviced
We recommend boiler maintenance once a year, ideally in late summer or early fall. Our heating season is long, and boilers that also serve radiant floors or snowmelt can run most of the year. For a homeowner’s checklist on timing, see our guide to boiler maintenance before winter. If you want maintenance on a set schedule, our Home Care Plan keeps it on the calendar.
What You Can Do Between Visits
A few simple checks help you catch problems early.
- Note whether the pressure gauge stays in its usual range.
- Look under the relief valve discharge pipe for drips or stains.
- Watch for water around the boiler, pumps, and valves.
- Clear snow away from outdoor intake and exhaust vents after storms.
- Listen for new banging, gurgling, or whistling.
If you are not sure what a new sound means, our post on why boilers make strange noises explains the common causes. Leave burner and valve work to a professional. If you smell gas, leave the house and call your gas utility from outside. If the relief valve is discharging or pressure reads well above normal, turn the boiler off and call us.

Schedule Boiler Maintenance with Mountain Standard Plumbing
Contact Mountain Standard Plumbing or call today to schedule boiler maintenance for your home in Cherry Hills Village, Littleton, or Greenwood Village. Your visit covers combustion, safety controls, circulation, and system water, with clear findings before any additional work.

$249
Boiler Tune-Up- Visual inspection to catch small issues early
- Heat exchanger cleaning
- Fernox F1 Express treatment to prevent rust and sludge
Expires: Nov 30, 2026
Contact Us
What your neighbors in South Metro Denver are asking



